收藏本站
ZXLD1321
Low voltage operation (start-up mode)
For supply voltages below 2V, the normal control loop will have insufficient headroom to operate
reliably. This condition is detected by the 'under-voltage comparator', which compares a fraction
of the internal supply voltage (Vcc) against VREF. When the comparator output is active
(Vcc<1.8V), the output of the normal switch drive circuit is disabled and an alternative 'Start-up
oscillator and driver' enabled. The start-up oscillator provides a nominal 50kHz fixed frequency
drive signal to the base of the switch transistor, which is independent of VADJ and the voltage on
CFB. Under low voltage conditions, the peak current in the coil ramps to approximately 25% of
the normal value and the "OFF" time is fixed.
The low voltage start-up mode allows the device to operate down to 1.2V nominal. This allows
the chip to work from a single cell in boost mode and by configuring the device in Bootstrap
mode, normal operation of the control loop will occur once the output has risen above 2.2V.
Details of Bootstrap-Boost mode are given in the application notes.
ADJ pin
The ADJ pin is connected to the internal 500mV reference (VREF) via a 100k resistor. This biases
the ADJ pin to the reference voltage and defines nominal 100% LED current.
The ADJ pin can be overdriven with an external dc voltage between 50mV and 500mV to reduce
the LED current proportionally between 10% and 100% of the nominal value.
LED current can also be adjusted by applying a low frequency PWM signal to the ADJ pin to turn
the device On and Off. This will produce an average output current proportional to the duty cycle
of the control signal.
The device can be shut down by shorting the ADJ pin to ground, or pulling it to a voltage below
28mV with a suitable open collector NPN or open drain NMOS transistor. In the shutdown state,
most of the circuitry inside the device is switched off and residual quiescent current will be
typically 12μA.
Thermal control of LED current
The 'Thermal compensation current' circuit produces a sourcing current (Itc) which is zero for
voltages above 75mV on TADJ and increases to 100μA when TADJ falls to 50mV. This current is
summed into the control node and subtracted from the demand current, causing LED current to
reduce from 100% down to zero over this input range. The potential divider, consisting of a fixed
resistor Rt and an NTC Thermistor Rth between VREF and ground, defines the voltage on TADJ
and sets the threshold temperature. Further details are given in the application notes.
The Thermal Control feature can be disabled by leaving the TADJ pin floating, or by connecting
it to VREF.
Over-temperature shutdown
The ZXLD1321 incorporates an over-temperature shutdown circuit to protect the device against
damage caused by excess die temperature, resulting from excessive power dissipation in the
switch. The output of the 'Over-temp Shutdown' circuit will go high when the die temperature
exceeds 150°C (nominal). This will turn off the drive to the switch during normal operation.
Operation will resume when the device has cooled to a safe level.
Issue 1 - January 2008
? Zetex Semiconductors plc 2008
10
www.zetex.com
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ZXLD1322DCCTC IC LED DRIVR WHITE BCKLGT 14-DFN
ZXLD1350ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD1352ET5TA IC LED DRIVER HIGH BRIGHT TSOT-5
ZXLD1356DACTC IC LED DRIVER WHITE BCKLGT 6-DFN
ZXLD1360ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD1362ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD1366DACTC IC LED DRIVER WHITE BCKLGT 6-DFN
ZXLD1370EST16TC IC LED DRVR HIGH BRIGHT TSSOP-16
相关代理商/技术参数
ZXLD1322 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:BUCK/BOOST MODE DC-DC CONVERTER
ZXLD1322DCCTC 功能描述:直流/直流开关转换器 Buck-Boost DC-DC Con 0.7A output RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
ZXLD1322DCCTC-CUT TAPE 制造商:DIODES 功能描述:ZXLD1322 Series 15 V 600 kHz 700 mA Buck/Boost Mode DC-DC Converter - DFN-14
ZXLD1322DCTC 制造商:ZETEX 制造商全称:ZETEX 功能描述:Buck/boost mode DC-DC converter for LED driving with 700mA output and current control
ZXLD1350 制造商:ZETEX 制造商全称:ZETEX 功能描述:350mA LED driver with internal switch
ZXLD1350_07 制造商:ZETEX 制造商全称:ZETEX 功能描述:350mA LED driver with internal switch
ZXLD1350ET5 制造商:Diodes Incorporated 功能描述:LED DRIVER INTERNAL SWITCH SMD 制造商:Diodes Incorporated 功能描述:LED DRIVER, INTERNAL SWITCH, SMD 制造商:Diodes Incorporated 功能描述:IC, LED DRIVER, BUCK, TSOT-23-5; Topology:Buck (Step Down); No. of Outputs:1; Output Current:350mA; Output Voltage:30V; Driver Case Style:TSOT-23; Input Voltage Min:7V; Input Voltage Max:30V; Dimming Control Type:PWM / DC ;RoHS Compliant: Yes
ZXLD1350ET5TA 功能描述:LED照明驱动器 7-30V Input 350mA w/Internal Switch RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N